new yamzuki RGV 421cc
Moderator: rztom
new yamzuki RGV 421cc
my new project
yamzuki
base banshee motor in rgv frame fork gsxr 750 srad 98 with wheel ,
swing arm r6 with linkage and shok, wheel bandit 600 4.5" for 160/70/17 or wheel gsxr srad 750 but 190/50/17 is too big but it's good tyre lol
for the motor i have already 421cc but i want more and more so the must i think, its cheetah in 72mm with exhaust valve and +7 crank ....
i have rgv carbs 32mm and 421 exhaust's wicked ! it's good for 421 but for 480cc ....
By daftmetal at 2012-01-21
By daftmetal at 2012-01-21
By daftmetal at 2012-01-21
it's first test "cradle test"
cradle weld
By daftmetal at 2012-01-21
By daftmetal at 2012-01-21
this cradle is an prototype
the final will be in aluminium
the swing arm r6 2005
By daftmetal at 2012-01-21
the fork
By daftmetal at 2012-01-21
yamzuki
base banshee motor in rgv frame fork gsxr 750 srad 98 with wheel ,
swing arm r6 with linkage and shok, wheel bandit 600 4.5" for 160/70/17 or wheel gsxr srad 750 but 190/50/17 is too big but it's good tyre lol
for the motor i have already 421cc but i want more and more so the must i think, its cheetah in 72mm with exhaust valve and +7 crank ....
i have rgv carbs 32mm and 421 exhaust's wicked ! it's good for 421 but for 480cc ....
By daftmetal at 2012-01-21
By daftmetal at 2012-01-21
By daftmetal at 2012-01-21
it's first test "cradle test"
cradle weld
By daftmetal at 2012-01-21
By daftmetal at 2012-01-21
this cradle is an prototype
the final will be in aluminium
the swing arm r6 2005
By daftmetal at 2012-01-21
the fork
By daftmetal at 2012-01-21
Last edited by toni on Sat Mar 31, 2012 11:01 am, edited 1 time in total.
vj21 to 421cc
Chain clearance
toni,
Didn't you already build one of these?
Anyway, I am building a similar machine. I may be wrong, but I would be shocked if you have clearance of the chain and the lower frame crossbar below the swing arm. You may need to raise the engine both front and rear to get the clearance you will need for the chain to clear that crossbar.
My rear mount practically touches the other frame crossbar above the swing arm and the clearance is not ideal. I will likely add a plastic chain guide on the lower crossbar.
Why not go with the newer R6 swing arm like RGVRespect did on his?
Good luck with your project!
Didn't you already build one of these?
Anyway, I am building a similar machine. I may be wrong, but I would be shocked if you have clearance of the chain and the lower frame crossbar below the swing arm. You may need to raise the engine both front and rear to get the clearance you will need for the chain to clear that crossbar.
My rear mount practically touches the other frame crossbar above the swing arm and the clearance is not ideal. I will likely add a plastic chain guide on the lower crossbar.
Why not go with the newer R6 swing arm like RGVRespect did on his?
Good luck with your project!
Nice work on those cradles.
That is a great looking project.
That is a great looking project.
Ken's Garage
https://www.youtube.com/c/KensGarage1
https://www.youtube.com/c/KensGarage1