CARB RZ350 EXTRA PART UGH
Moderator: rztom
CARB RZ350 EXTRA PART UGH
I JUST REBUILT THRE CARBS ON THE RZ350 AND AFTER ALL ASSEMBLED , THERE WAS A BUSHING LEFT LAYING ON THE BENCH. I TOOK THEM APART AGAIN AND CAN NOT FIND A PLACE FOR IT ..THE PIN THAT IS ON BOTH CARBS THAT SECURE THE SLIDE HAS THE WASHER AND BUSHING ON BOTH SIDES OF IT. JUST DO NOT KNOW WHERE THIS ONE WOULD GOE.. PARTS BOOK DOES NOT SHOW ANOTHER BUSHING. THE BUSHING IS 14MM OD ,8MM ID AND 4.8MM THICK. IT IS THE RIGHT SIZE ID FOR THE SLIDE PIN TO GO THROUGH BUT THERE IS NO PLACE TO PUT IT.
Last edited by hotshoe93 on Mon Dec 03, 2018 12:49 pm, edited 1 time in total.
84 RZ350 Toomey
2003 FZ1 Yellow/Black
BULTACO ASTRO
Champion framed Kawasaki F81m
BULTACO SHERP-S Brakeless Dirt tracker
ZUK A-100 w/ FACTORY HOP UP
2003 FZ1 Yellow/Black
BULTACO ASTRO
Champion framed Kawasaki F81m
BULTACO SHERP-S Brakeless Dirt tracker
ZUK A-100 w/ FACTORY HOP UP
Re: CARB RZ350 EXTRA PART UGH
another quick spec. the bushing is white plastic just like the one on the pins the activate the slides ??? Thx
84 RZ350 Toomey
2003 FZ1 Yellow/Black
BULTACO ASTRO
Champion framed Kawasaki F81m
BULTACO SHERP-S Brakeless Dirt tracker
ZUK A-100 w/ FACTORY HOP UP
2003 FZ1 Yellow/Black
BULTACO ASTRO
Champion framed Kawasaki F81m
BULTACO SHERP-S Brakeless Dirt tracker
ZUK A-100 w/ FACTORY HOP UP
- Evans Ward
- -----
- Posts: 1546
- Joined: Sun Jun 07, 2009 6:39 pm
- Location: Macon, GA
Re: CARB RZ350 EXTRA PART UGH
Can you post a pic? I’m running stockers and have rebuilt mine many times and may be able to help.
84 RZ350-Toomeys,SCR milled head, stk 26 carbs,300 M, 35 P, stock regrooved needles AS 2.5 turns out,stk air box,Banshee reeds Zeel non-progr CDI,TSRL Program YPVS,alum rad,R6 shock,GV emulators w/RT springs,fork brace,Shindy steering damper.
- Evans Ward
- -----
- Posts: 1546
- Joined: Sun Jun 07, 2009 6:39 pm
- Location: Macon, GA
Re: CARB RZ350 EXTRA PART UGH
Does this help?
84 RZ350-Toomeys,SCR milled head, stk 26 carbs,300 M, 35 P, stock regrooved needles AS 2.5 turns out,stk air box,Banshee reeds Zeel non-progr CDI,TSRL Program YPVS,alum rad,R6 shock,GV emulators w/RT springs,fork brace,Shindy steering damper.
- Evans Ward
- -----
- Posts: 1546
- Joined: Sun Jun 07, 2009 6:39 pm
- Location: Macon, GA
Re: CARB RZ350 EXTRA PART UGH
Is it #3 listed above?
84 RZ350-Toomeys,SCR milled head, stk 26 carbs,300 M, 35 P, stock regrooved needles AS 2.5 turns out,stk air box,Banshee reeds Zeel non-progr CDI,TSRL Program YPVS,alum rad,R6 shock,GV emulators w/RT springs,fork brace,Shindy steering damper.
Re: CARB RZ350 EXTRA PART UGH
I was thinking my extra spacer (4.8mm) went in The #4 spot but I put in that spot it seems to be just a tad big.. I know 2 and 3 are correct I have a small,thin (washer/spacer maybe .5mm)) in the 4 spot now. Maybe the .5mm pacer goes in spot 1 and I could try to but the extra one (4.8mm) that I have in #4 again ?? your showing #1as a medium spacer, have any idea the width of it ?? I assume the #1 and #4 positions u a r pointing to are under the3 screwed cap ?? Thx a bunch.. I third to post a pic but not sure how yet as it says file is to big,. kinda new at this...
1 more thing I don't think my parts book / manual shows any spacers in the #1 position.
are # 1 #2 the same size ?
1 more thing I don't think my parts book / manual shows any spacers in the #1 position.
are # 1 #2 the same size ?
84 RZ350 Toomey
2003 FZ1 Yellow/Black
BULTACO ASTRO
Champion framed Kawasaki F81m
BULTACO SHERP-S Brakeless Dirt tracker
ZUK A-100 w/ FACTORY HOP UP
2003 FZ1 Yellow/Black
BULTACO ASTRO
Champion framed Kawasaki F81m
BULTACO SHERP-S Brakeless Dirt tracker
ZUK A-100 w/ FACTORY HOP UP