Hi, that cylinder is for the later model as in ypvs.kobra wrote: ↑Mon Sep 23, 2019 6:24 pm Is this the correct side that could work for ya?
https://www.ebay.com/itm/Yamaha-RZ350-L ... Sw31pdbZnz
Search found 33 matches
- Wed Sep 25, 2019 12:04 pm
- Forum: Engines
- Topic: Would you run it?
- Replies: 38
- Views: 3419
Re: Would you run it?
- Fri Feb 01, 2019 6:15 am
- Forum: Racing Discussion
- Topic: Isle of Man TT 2019
- Replies: 124
- Views: 47002
Re: Isle of Man TT 2019
good luck with your plan to visit the IOM tt . There are plenty of well run camp sites to choose from . I have camped, stayed in home stay ,and had an hotel stay . Must say I enjoyed them all but camping was more of a laugh . There are a few blokes who live there that have got Lc's . https://youtu.b...
- Sun Dec 10, 2017 9:05 am
- Forum: RD350LC 4L0 - For ELSIE Owners
- Topic: Securing ur Elsie
- Replies: 14
- Views: 3181
Re: Securing ur Elsie
Had an unwanted visit to my lock up some months ago . lucky for me nothing taken. Paranoid , set in and I bought new locks ,disc locks and chain. I also bought some flat steel 80mmx8mm and made a couple of ground anchors . when I got the one anchor installed I bought a length of Pewag 14mm chain and...
- Sun Nov 05, 2017 4:24 pm
- Forum: RD350LC 4L0 - For ELSIE Owners
- Topic: LC SEPERATE CYLINDERS WHY
- Replies: 5
- Views: 1371
Re: LC SEPERATE CYLINDERS WHY
Yes maybe the tz cylinders were cast in one unit because the bores were plated . Lc cylinders have iron liners.
- Sun Sep 03, 2017 5:46 am
- Forum: Engines
- Topic: Lubrication holes in piston skirts good idea or not.
- Replies: 22
- Views: 9839
Re: Lubrication holes in piston skirts good idea or not.
Hi , not been here for some time . On all the engines I have rebuilt /2 stroke ,I chamfer the bottom edge of the pistons off to help stop the sharp edge scraping the oil off . Works for me.
- Tue Apr 11, 2017 4:31 pm
- Forum: Engines
- Topic: 1990 F2 Wont Rev out past 6k
- Replies: 39
- Views: 9946
Re: 1990 F2 Wont Rev out past 6k
Hi ,make sure the power valves are set correctly. as in opening as the revs go up .
- Sat Dec 10, 2016 3:55 pm
- Forum: Engines
- Topic: Plating Steel Cylinders
- Replies: 14
- Views: 5539
Re: Plating Steel Cylinders
Had my 350 LC cylinders relined a couple of years ago. if I remember right it cost 360 odd pounds . Armstrong engineering did the job ok so far, not done the mileage like I use too though so still running in .
- Thu Dec 08, 2016 5:00 am
- Forum: Engines
- Topic: Plating Steel Cylinders
- Replies: 14
- Views: 5539
Re: Plating Steel Cylinders
As has been said a plated cylinder will last longer providing there is no piston/ring/clip /bearing failure that marks the bore. I have an rgv250 which has plated bores . I was told to replace pistons and rings every 10,000 miles. Yes the plating is not cheap. A couple of years ago I had a pair of 3...
- Thu Nov 03, 2016 3:08 pm
- Forum: RD350LC 4L0 - For ELSIE Owners
- Topic: boring out cylinders
- Replies: 20
- Views: 7174
Re: boring out cylinders
Hi , I know of a motorcycle engineer who built a big bore lc for one of his customers some 30 years ago. he said he machined the cylinders out and relined them with bultaco 250 liners. he also fitted rd400 rods to the crank shaft . what he did say was the transfer tunnels got narrow because of the b...
- Thu Nov 03, 2016 2:48 pm
- Forum: Engines
- Topic: NEED to disconnect the Power Valve coupler b4 cyl removal?
- Replies: 18
- Views: 6577
Re: NEED to disconnect the Power Valve coupler b4 cyl remova
Oh dear , prepare to massage the old wallet . lol
- Mon Mar 14, 2016 11:59 am
- Forum: Engines
- Topic: All new RZ 385 +4mm stroker pipes
- Replies: 10
- Views: 3822
Re: All new RZ 385 +4mm stroker pipes
stands ,stands whats up with you slack jaws that's just extra weight lol. Glyn nice pipes, if only my tig welding looked half as good .
- Mon Jan 18, 2016 4:35 am
- Forum: Engines
- Topic: good news ..bad news
- Replies: 28
- Views: 3738
Re: good news ..bad news
uk coins as in pennies and 2p piece are made of steel with a plating on so I use a piece of flat copper tube now to go in the gears to lock them up.
- Sun Jan 17, 2016 2:52 pm
- Forum: Engines
- Topic: good news ..bad news
- Replies: 28
- Views: 3738
Re: good news ..bad news
Repair the cases it should be easy enough for an experienced aluminium welder. I certainly wouldn't chuck them.
- Mon Mar 23, 2015 5:31 am
- Forum: Engines
- Topic: New piston mistake
- Replies: 17
- Views: 6353
Re: New piston mistake
Glyn, nice video your bike was going well.you were showing them what a stinkwheel could do lol.
- Sun Nov 30, 2014 6:25 am
- Forum: RD350LC 4L0 - For ELSIE Owners
- Topic: steeleys lc 350
- Replies: 0
- Views: 1269
steeleys lc 350
fitted some swarbrick end cans to my nikkon pipes and had a ride up the road.https://www.youtube.com/watch?feature=p ... Zq0ooK6OsA" onclick="window.open(this.href);return false;