My project (1GE)

[Bengt Weil]

I would be interested when these pieces become available as well... Thanks!

[Speed Freak]

Still some work to do... Most complex lock of all 4.



But now I want to have some drinks...
Happy new year

[HWY9CA]

Happy New Years to you...

You have some sought after skills in CAD...

Watching this one.


JT

[Speed Freak]

Playing around with rendering options...



Don`t know whe I can go back to the garage, -20°C outside at the moment.

[Kalim]

Wow! This air box is nice!

-20° !? , I understand you'd rather spend time on the CAD !

[Smoker]

Don`t know whe I can go back to the garage, -20°C outside at the moment.

Will you attempt to CAD draw the RZV frame?

Would be valuable to those of us who want to do frame mods.

Did you CAD draw the swingarm?

The CAD airbox is amazing!

[pstamper]

I will never complain about the cold again. Holidays are over and most of my bike is ready for reassembly. I will find the cheapest way to get the rotors too you.

[Speed Freak]

More parts:

Some more details needed on the upper air filter case and the "cover" (no.37) is missing.

Can someone send me a picture and dimensions of following parts?


24 - 92501-06020
25 - 92901-06600
Should be a silver cross head screw M6x20 with captive washer (diameter 12,9mm and 1mm thick) but I don`t really trust them because one of the 4 is different...

38 - 97701-50116
39 - 92901-05200
The washer is missing on my bike and I don`t know if the screw is original (cross head, 25mm long with plastic thread outer diameter 5mm and inner diameter ~3,5mm)

Regarding RZV frame - i dont have one, so it`s a bit hard to get it into CAD.
Planning to do the steel frame as I need something to hold all the small CAD parts which I have already done together
but I don`t know how I can measure all angles etc. accurate enough - a 3D scan including the front bracket and the rear frame would be nice

I have done the swing arm 2 years ago, but here also the same problem, I don`t have the tools at home to measure such big parts really accurate.
Accurate enough for me at the moment, but for really working with the parts at least the main geometry (lengt between bearing and axle, exact position of the linkage bolt) needs to be refined - at the moment maybe ~+-3mm

[RC45]

Playing around with rendering options...



Don`t know whe I can go back to the garage, -20°C outside at the moment.

Nice one.

Have you done the engine cases yet?

Don`t know whe I can go back to the garage, -20°C outside at the moment.

Will you attempt to CAD draw the RZV frame?

Would be valuable to those of us who want to do frame mods.

Did you CAD draw the swingarm?

The CAD airbox is amazing!

I am about to do the RZV and RZ frame.

I have no need for the stock swinger but will draw it up for the community

[Smoker]

I am about to do the RZV and RZ frame.

I have no need for the stock swinger but will draw it up for the community

That is awesome!

The CAD work you and Speed Freak are doing is mind blowing.

[rd84]

Really nice drawings - thanks for sharing.

Cheers
Paul

[jackson.40]

Speed Freak wrote

24 - 92501-06020
25 - 92901-06600
Should be a silver cross head screw M6x20 with captive washer (diameter 12,9mm and 1mm thick) but I don`t really trust them because one of the 4 is different...

This is correct, i just checked on my 1GE bike and I have the same.

There is a mistake on the 47X parts list which shows this screw as part number 92501-06025 but it should be 92501-06020.

38 - 97701-50116
39 - 92901-05200
The washer is missing on my bike and I don`t know if the screw is original (cross head, 25mm long with plastic thread outer diameter 5mm and inner diameter ~3,5mm)

Do you have a photo?

Steve

[RC45]

I am about to do the RZV and RZ frame.

I have no need for the stock swinger but will draw it up for the community

That is awesome!

The CAD work you and Speed Freak are doing is mind blowing.

I don't mean to hijack Speeds build thread, but I am not sure where to put general RZ CAD renderings and possible down load links, so I will just provide a teaser for the swing arm

[Speed Freak]

Including the ejection pin spots

[RC45]

Well, those are cast pieces we must be true to life LOL