Here's one for yer...
For some reason.....when I switch my ignition on.....my Ypvs Servo has started to just go round and round....
Just...zzzzzzzzzzzzzzzzzzzzzz
Instead of zzzzz (one way) then zzzzz (the other way) lolol
Any thoughts???
Ypvs Servo
Moderator: rztom
Ypvs Servo
I'd rather be scared to death than bored to death!
Re: Ypvs Servo
There are 2 possible causes :
1 : The position sensor in the motor is out of order. Never heard of this but theoritically possible. Sensor is a potentiometer and is easy to check : see service manual for more details.
2 : The most probably with 99,99 % of chance : Your YPVS control box is out of order. Typical symptom, I had the same default. Contact Nick at 2t-racelab.com, he will repair it if possible.
1 : The position sensor in the motor is out of order. Never heard of this but theoritically possible. Sensor is a potentiometer and is easy to check : see service manual for more details.
2 : The most probably with 99,99 % of chance : Your YPVS control box is out of order. Typical symptom, I had the same default. Contact Nick at 2t-racelab.com, he will repair it if possible.
Re: Ypvs Servo
Flat battery or very low charge is another possibility - attach a battery charger to the battery while the battery is still connected and see if the servo works ok.
Cheers
Paul
Cheers
Paul
Re: Ypvs Servo
No, if the battery is low, motor will simply move slowly or not at all. But if it happens to move, test procedure will be done normally.rd84 wrote:Flat battery or very low charge is another possibility - attach a battery charger to the battery while the battery is still connected and see if the servo works ok.
Cheers
Paul
Re: Ypvs Servo
Cheers guys.
Phildu31. It's a brand new Zeeltronic ypvs/cdi box that's being wired into a one off wiring loom for my YZR replica.
About 90% through it at the mo.....
Ypvs servo tested on ignition switch "ON"..... fine. Has been since initially wiring in.
Went in the garage t'other day to start wiring the Kosovo clocks on.....but before I did I switched the ignition on......Zzzzzzzzzzzzzzzzzzzzzzzzzzzz.....Constant going round now for no reason!!!
No Idea why.
Phildu31. It's a brand new Zeeltronic ypvs/cdi box that's being wired into a one off wiring loom for my YZR replica.
About 90% through it at the mo.....
Ypvs servo tested on ignition switch "ON"..... fine. Has been since initially wiring in.
Went in the garage t'other day to start wiring the Kosovo clocks on.....but before I did I switched the ignition on......Zzzzzzzzzzzzzzzzzzzzzzzzzzzz.....Constant going round now for no reason!!!
No Idea why.
I'd rather be scared to death than bored to death!
Re: Ypvs Servo
So you replaced the original YPVS box with a Zeeltronic one...Just an unimportant detail.
Would have been honest to say it before.
Would have been honest to say it before.
Re: Ypvs Servo
Are the pulley cables attached to the pvs?
Am sure it s not
M.
Am sure it s not
M.
my bikes :RD500 2X ,RD 350 F2 , RD 350 31K,RD350 4LO,RG500,RG250 WW,RGV250,TZR250 3MA,TZR250 3XV,NS400r,NSr250 mc21,KR1250S,