Search found 67 matches
- Tue Feb 12, 2019 3:44 am
- Forum: Engines
- Topic: YZ85 reed valves.....are they worth the effort?
- Replies: 27
- Views: 8341
Re: YZ85 reed valves.....are they worth the effort?
hi that cost a little bit but VForce V3 reed valves are a good solution with just a litlle griding. Is this the best Price/HP result ? Idon't know
- Tue Jan 15, 2019 4:16 am
- Forum: Member's Rides
- Topic: RDN 500 2019
- Replies: 7
- Views: 3188
Re: RDN 500 2019
Love it and great job. Need dry clutch and that will be perfect.
Cheers
Cheers
- Tue Oct 09, 2018 5:04 pm
- Forum: Member's Rides
- Topic: Sunday ride
- Replies: 6
- Views: 3024
- Sun Aug 19, 2018 4:45 am
- Forum: Custom Projects/Restoration
- Topic: rd 500 racer R6 bike
- Replies: 24
- Views: 6589
Re: rd 500 racer R6 bike
Nice job, but I think R1 2004 saddle is more nice for this bike with pipe under saddle.
cheers
cheers
- Thu Jun 14, 2018 2:49 am
- Forum: Custom Projects/Restoration
- Topic: My 500 YZR screamer project
- Replies: 54
- Views: 22036
Re: My 500 YZR screamer project
HI, After 2 sessions for running-in with and also learning the track, the thrid one was more funny. Engine run very well into the high rpm and no problem with the low rpm. 270 main jet and 15 pilot jet seems to be ok. Now I have to adjust needle setting. I beleive I'm to rich but I'll try to make a ...
- Wed Jun 13, 2018 2:42 pm
- Forum: Bimota V-Due
- Topic: Aprilia RSW 500 replica
- Replies: 57
- Views: 46032
Re: Aprilia RSW 500 replica
Amazing AX, I love it
- Sun Jun 10, 2018 6:59 pm
- Forum: Custom Projects/Restoration
- Topic: My 500 YZR screamer project
- Replies: 54
- Views: 22036
Re: My 500 YZR screamer project
Ready for a come back on track. Hope jI have the good jetting because if I to adjust it I have to remove the tank, and the radiator !!! Now jetting is #270 for the main and #15 for jet pilot (350 and 20 for the original setting). @3XV, according to your information I have removed the 240. I hope I w...
- Sat Jun 02, 2018 6:41 am
- Forum: Custom Projects/Restoration
- Topic: My 500 YZR screamer project
- Replies: 54
- Views: 22036
Re: My 500 YZR screamer project
Hi for the front pistons, I'm sure that comes from the ignition timing because it was non good, but for the rear one, I don't know. My oil pump ?
- Sun May 27, 2018 4:14 am
- Forum: Custom Projects/Restoration
- Topic: My 500 YZR screamer project
- Replies: 54
- Views: 22036
Re: My 500 YZR screamer project
Hi, After several runs on track only for training, engine needed some attention. During my last run (October 2017) my filghwheels were noisy. Top speed was good but accellaration was not fully good. Once the engine out of the frame, I quickly understood that winter will be a study winter with lot of...
- Mon May 14, 2018 2:48 am
- Forum: Engines
- Topic: carburettors Mikuni TM 35 setup?
- Replies: 15
- Views: 4144
Re: carburettors Mikuni TM 35 setup?
Hi 3XV,
how does the bike run now? Any dtno or track test ? Always you double jetting 280-310 ?
cheers
how does the bike run now? Any dtno or track test ? Always you double jetting 280-310 ?
cheers
- Wed Jan 24, 2018 5:59 pm
- Forum: Custom Projects/Restoration
- Topic: RZ500 Street Fighter
- Replies: 47
- Views: 20531
Re: RZ500 Street Fighter
Hi Ron,
when you have wrotten ''Bill Wilson opens the rubber manifolds'' you are talking about the inlet, outlet or both?
regards
when you have wrotten ''Bill Wilson opens the rubber manifolds'' you are talking about the inlet, outlet or both?
regards
- Sun Jan 21, 2018 6:29 am
- Forum: Custom Projects/Restoration
- Topic: Race outfit RD 500 (Abe #9)
- Replies: 61
- Views: 12675
Re: Race outfit RD 500 (Abe #9)
Congratulations for the 500 cc
You have a sensor near the rear cliper what is this for ?
You have a sensor near the rear cliper what is this for ?
- Fri Jan 12, 2018 3:54 pm
- Forum: Custom Projects/Restoration
- Topic: RZ500 Street Fighter
- Replies: 47
- Views: 20531
Re: RZ500 Street Fighter
HI Ron,
great bike and 110 Hp to the rear wheel is a great power.
Do you have somes pics of the tuning manifolds ?
What is the setting of your TMX ?
Regards Nick
great bike and 110 Hp to the rear wheel is a great power.
Do you have somes pics of the tuning manifolds ?
What is the setting of your TMX ?
Regards Nick
- Thu Jan 11, 2018 7:07 am
- Forum: Engines
- Topic: carburettors Mikuni TM 35 setup?
- Replies: 15
- Views: 4144
Re: carburettors Mikuni TM 35 setup?
Hi I have a question about the spacer.
Why did you use is and why 6 mm?
I also want to fit 35 TMX on my RS/RD engine but without any spacer. For now my bike is running with 32 koso wothout spacer.
Why did you use is and why 6 mm?
I also want to fit 35 TMX on my RS/RD engine but without any spacer. For now my bike is running with 32 koso wothout spacer.
- Mon Nov 20, 2017 6:31 pm
- Forum: Engines
- Topic: Dry clutch conversions contact info
- Replies: 3
- Views: 1259