Search found 10 matches
- Fri Jul 06, 2018 12:37 pm
- Forum: Engines
- Topic: Ivans needles
- Replies: 3
- Views: 911
Ivans needles
I have an Ivans needle set with A and B needles. Does anyone know which needles i use for a standard RD500?
Re: fuel cock
Thanks SpeadFreak.... Perfect!
fuel cock
For the avoidance of doubt can someone please tell me the correct way to connect fuel pipes to the petcock. Top, middle right and bottom for the larger diameter hoses. Is the top point the fuel hose to the carbs? Bottom point of fuel petcock connected to "On" side of fuel tank? Middle righ...
- Thu Dec 28, 2017 2:51 pm
- Forum: Electrical & Wiring
- Topic: rev counter not responding to revs
- Replies: 1
- Views: 857
rev counter not responding to revs
Thanks in advance to any help with fixing my rev counter.... After the engine is running, its a few minutes before the rev counter starts to work. Firstly it only shows around 1,500rpm. After a short ride it will only register up to 4,000rpm even if I am way higher than that. Any advice on what coul...
- Sun Dec 24, 2017 10:23 am
- Forum: Electrical & Wiring
- Topic: Ignition coils
- Replies: 9
- Views: 1923
Re: Ignition coils
Thanks for all the assistance.
- Sat Dec 23, 2017 3:30 pm
- Forum: Electrical & Wiring
- Topic: Ignition coils
- Replies: 9
- Views: 1923
Ignition coils
Thanks in advance for any recommendations on ignition coil replacement.... I see lots on eBay, are they OK to use?
- Fri Dec 22, 2017 1:04 pm
- Forum: Engines
- Topic: RZ carbs to RD500
- Replies: 2
- Views: 964
RZ carbs to RD500
Hi, I have read so many posts etc but I am still not 100% sure as what i need to change when putting RZV carbs on a RD500. What do i need to change? I think just the main jet to a 165 yes? I can leave the pilot jet and the pilot air jet (in the intake bell mouth) and the emulsion tubes as is yes? Th...
- Fri Dec 15, 2017 5:19 pm
- Forum: Engines
- Topic: Fuel pipe kit
- Replies: 1
- Views: 752
Fuel pipe kit
Hi,
Does anyone do a replacement fuel hose kit from the petcock to the carbs? Or does anyone know the diameters required from petcock to T junction and then T junction to each bank of carbs and then from top carb to lower carbs?
Thanks in advance for any help.
Does anyone do a replacement fuel hose kit from the petcock to the carbs? Or does anyone know the diameters required from petcock to T junction and then T junction to each bank of carbs and then from top carb to lower carbs?
Thanks in advance for any help.
- Sun Dec 10, 2017 8:34 am
- Forum: Engines
- Topic: YPVS adjustment
- Replies: 4
- Views: 1005
YPVS adjustment
Please assist....
Do I adjust the YPVS cables, using the 8mm bolt method, with the ignition on of off?
Do I adjust the YPVS cables, using the 8mm bolt method, with the ignition on of off?
- Thu Dec 07, 2017 2:18 pm
- Forum: Engines
- Topic: Carb set up/sync
- Replies: 1
- Views: 706
Carb set up/sync
Hi,
Can anyone enlighten me into how to set up/sync the carbs on my RD500 please. Mainly the throttle valve height.
Thanks in advance for any assistance.
Can anyone enlighten me into how to set up/sync the carbs on my RD500 please. Mainly the throttle valve height.
Thanks in advance for any assistance.