Search found 73 matches
- Mon Jun 19, 2023 1:16 pm
- Forum: Electrical & Wiring
- Topic: pick up gap
- Replies: 4
- Views: 632
Re: pick up gap
Before buying a zeel, measure the resistance of the pickup coil, and the ignition coils. Also the stator coils. Then check the ignition cable for rotten copper wire where they're plugged into the coils and the plug cap. Last but not least check your kill switch. It might also help to install a separ...
- Sat Jun 17, 2023 2:36 am
- Forum: Electrical & Wiring
- Topic: pick up gap
- Replies: 4
- Views: 632
Re: pick up gap
This i posted some weeks ago concerning gap adjustment: Another simple thing is to measure the pickup gap. 1. Measure the diameter of the rotor between the two pickup surfaces. Devide by two- that’s no.1 to note. Then measure the diameter of the stator . These core segments are turned precisely to a...
- Wed May 17, 2023 10:48 am
- Forum: Engines
- Topic: 1984 RZ500 clutch slipping BADLY
- Replies: 14
- Views: 2903
Re: 1984 RZ500 clutch slipping BADLY
Don't forget to give the pushrod enough play. Adjustable behind the rubber plug of the sprocket cover.
- Thu Jul 21, 2022 5:09 am
- Forum: Engines
- Topic: OEM Piston Weight
- Replies: 3
- Views: 1143
Re: OEM Piston Weight
Yes, they are the same weight
- Mon Mar 14, 2022 5:10 am
- Forum: Bodywork
- Topic: RZ500 Recommended Decal Kits
- Replies: 3
- Views: 894
Re: RZ500 Recommended Decal Kits
Hello Wolfgang
Have a look at decalmoto.com. I have received a Set for my black and red rd500. It is complete with all stripes and logos. The colours are matching really good.
Olli
Have a look at decalmoto.com. I have received a Set for my black and red rd500. It is complete with all stripes and logos. The colours are matching really good.
Olli
- Tue Aug 24, 2021 12:44 pm
- Forum: Engines
- Topic: Remove the balance shaft
- Replies: 4
- Views: 2237
Re: Remove the balance shaft
I was thinking about this too for a while but it is a lot of work to do, especially of it is not as expected. You can try it, by just uncoupling the balancer. remove the gear and run it. The challenge is , you should fix the balancer against free rotation then, as it will start to rotate freely to f...
- Wed May 05, 2021 3:47 am
- Forum: Chassis, Brakes & Suspension
- Topic: Tyres and brakes
- Replies: 6
- Views: 1724
Re: Tyres and brakes
Bridgestone S22 R is my favorite since I have this bike
- Mon Apr 19, 2021 7:53 am
- Forum: Engines
- Topic: Gear lever
- Replies: 1
- Views: 644
Re: Gear lever
You can drill. IT Out and replace it with a Standard joint with a screw
- Sun Jan 10, 2021 8:58 am
- Forum: Engines
- Topic: Rear Crank Timing out 2.5 Degrees
- Replies: 70
- Views: 10448
Re: Rear Crank Timing out 2.5 Degrees
Me too, please
PM sent
Olli
PM sent
Olli
- Fri Jun 26, 2020 6:56 am
- Forum: Engines
- Topic: lower bank does not fire up
- Replies: 22
- Views: 2942
Re: lower bank does not fire up
Hey franco
If you did connect the plus wire of the bottom coil ( with wire extension ) to the bottom coil, and it didn’t fire the bottom cylinders, then it can be a fouling coil. Change the coils from top to bottom!
If you did connect the plus wire of the bottom coil ( with wire extension ) to the bottom coil, and it didn’t fire the bottom cylinders, then it can be a fouling coil. Change the coils from top to bottom!
- Mon Jun 22, 2020 3:58 pm
- Forum: Electrical & Wiring
- Topic: Backfire when kicking over -Zeeltronic
- Replies: 15
- Views: 3849
Re: Backfire when kicking over -Zeeltronic
Well I have tried to get it to stay open when kicking. No way so far. I tried to switch the starting and end angle. No chance, the servo starts to flicker . Programming 100 % to any low rpms won’t change the static behavior when you switch on the ignition. What we want for kicking. This starting ang...
- Mon Jun 22, 2020 3:23 am
- Forum: Electrical & Wiring
- Topic: Backfire when kicking over -Zeeltronic
- Replies: 15
- Views: 3849
Re: Backfire when kicking over -Zeeltronic
I think the PV is always closed at start, so programming fully open is not easily possible. To have it open , you might switch the pv cables at the servo mechanically. Your program should be vice versa then, starting with 100% And opening will be 0% then.
- Wed Jun 17, 2020 2:56 am
- Forum: Engines
- Topic: lower bank does not fire up
- Replies: 22
- Views: 2942
Re: lower bank does not fire up
Try to reduce gap to around 0.7 mm. Check the grounding of the lower coil. The minus terminal can be connected directly to the frame. Try to connect the plus wire from the top coil to the bottom coil.just to check if on your bottom plus line is something wrong. This would indicate a broken wire or I...
- Tue Jun 16, 2020 4:12 pm
- Forum: Engines
- Topic: Everybody: your squish height, Vcc and CR?
- Replies: 11
- Views: 2102
Re: Everybody: your squish height, Vcc and CR?
And before I forget, the oringed heads do not leak !!
- Tue Jun 16, 2020 4:06 pm
- Forum: Engines
- Topic: Everybody: your squish height, Vcc and CR?
- Replies: 11
- Views: 2102
Re: Everybody: your squish height, Vcc and CR?
Hey Franco, Sorry for not continuing my notes, had big trouble with misfiring on the first rides after. 10-20 km. Checked all ignition components, and replaced coils and cables. Saw some sparks jumping off the Top plugcaps to my electric support under the tank. but In the end, I had to rejet signifi...